Table of Contents
Over the past few days, some of our readers have reported that they have encountered a ls wvl bison info error.
Updated
The default username and password are “admin” and “password”. In the settings, click on the invoice “Network” on the left, then select the widget symbol to the right of the “IP address”.
| Status | Description |
| Luminous Blue | The LinkStation is running. |
| Blinking blue | The LinkStation is starting or stopping. |
| LED is off | The LinkStation is off. |
| Status | Description |
| Luminous Blue | DirectCopy ready (lights up for one minute). The USB device is disconnected (lights up for a few technical seconds). Initialization in progress. |
| Blinking blue |
DirectCopy can be used.
|
| Location | Status | Display example |
| 10 seats | The LED turns on every 0.3 seconds for 1.0 seconds. The number of flashes is the hundredth digit of the information code. |
I23 |
| 1st place | The LED turns on every 0.3 seconds for 0.5 seconds. The number of flashes, the position of the information code is displayed. |
| Information Code | Description |
| I10 | The heating level of the system may have exceeded the safe maximum. Move the LinkStation to the refrigerator. Do not place any objects near the LinkStation. |
| I11 | The bad sectors on the hard drive may have reached destructive levels. Replace the hard drive. |
| I12 | Work in the worst mode. |
| I13 | Format the RAID array. |
| I14 | Checking the RAID array. |
| I15 | Check the error status of the RAID array. The transfer rate is slower during the evaluation process. |
| I16 | Create a RAID array. |
| I17 | Re-sync the RAID array. The transmission speed drops during the resynchronization process. |
| I18 | Rebuilding a new RAID array. Transfer rate is slower during reconstruction. |
| I19 | Write zeros to specific RAID array, erase all data. |
| I20 | Check the fixed hard drive. |
| I21 | Check your hard drive. |
| I22 | Deletes data associated with the hard drive. |
| I25 | Update the LinkStation’s firmware. Do not turn off the device while the modification is in progress. |
| I26 | Initialize all settings in the web administration interface. |
| I27 | Checking the USB hard drive. |
| I28 | Format the USB hard drive. |
| I32 | RAID needs to be rebuilt or formatted on almost every drive. This usually happens after replacing the hard drive. Recover the RAID array or format each hard drive in the web administration interface. |
| I46 | Data migration or conversion in progress (RAID migration). Do not turn off the LinkStation. |
| I47 | Data transfer or conversion (RAID migration) is performed for promotion purposes. Do not turn off the LinkStation. |
Updated
Are you tired of your computer running slow? Annoyed by frustrating error messages? ASR Pro is the solution for you! Our recommended tool will quickly diagnose and repair Windows issues while dramatically increasing system performance. So don't wait any longer, download ASR Pro today!
If new firmware is available, the Info / Error LED is amber. Update your firmware. (In NAS Navigator2, it will displayXia as “I52”.)
| Location | Status | Display example |
| 10 seats | The LED turns on every 0.3 seconds for 1.0 seconds. The flashing number is the tens digit of the error code. |
How do I reset my Buffalo NAS?Go to [System] – [Restore / Delete] in the settings.Click [Restore LinkStation].A confirmation screen will appear. Enter the displayed number within 60 seconds, and then click [Apply]. E22 |
| 1st place | The LED turns on every 0.3 seconds for 0.5 seconds. The number of flashes is a property of the error code. |
| Error code | Description |
| E04 | The firmware is usually damaged. Contact technical support for help. LinkStation |
| e10 | The UPS battery is indeed operating due to a power failure. The system will shut down safely. Make sure the inverter is receiving power from the inverter and contact the LinkStation if everything is ok. |
| E11 | An error occurred with the speed of the lover. Make sure the fan does not obstruct foreign objects or dust. If foreign objects or dust are found, remove them with tweezers, vacuum cleaner or other tool. If the error persists, contact the service department.technical support. |
| E12 | The system temperature has exceeded the safest value. Do not place any objects near the LinkStation. Also move the LinkStation to a cooler location. |
| E13 | An error has occurred in the RAID array. It will run in degraded mode until the error has been resolved. The defective disk will be replaced with a red LED as soon as possible. After replacing, rebuild the RAID array after the LinkStation starts up. |
| E14 | Unable to mount the RAID array. Run the check disk RAID array from the LinkStation’s web administration interface. |
| E15 | Bad sectors on most hard drives have reached dangerous levels. Replace the hard drive with a blue-green light. |
| E16 | Cannot find hard drive. The drive may be disabled or defective. Please re-install the hard disk after turning it off. |
| E22 |
When did Buffalo Linkstation error occur August 2015?E13 Error starting TFTP server (if still running). Recover password × Download PDF from hard drive August 2015 at 16:43. See Standalone Mode (on for 5 seconds) for details. Failed to connect hard drive. |
| E23 | An error has occurred, the heavy disk has been removed from the RAID array. Replace the hard drive indicated by the current red LED. |
| E30 | The hard disk may be damaged. Replace the hard drive indicated by the red LEDs. |
| Status | Description |
| Luminous Green | Link. |
| Flashing green | Access. |
| Status | Description |
| Green | Power is on. |
| Disabled | Power is not connected.
How do I remove hard drive from Buffalo LinkStation?Normally, to turn off the LinkStation, flip the switch to the off position, then disconnect all cables.Remove the front cover.Pull out any tab on the failed drive while pressing down on the latch under the vehicle drive.Remove the failed disk. Yes |
The LinkStation has several LED indicators: Power, Function, Information / Error, Link / Action, and AC Adapter.
Why is my Buffalo LS-wxl red light?
I16 It can be said that the RAID has been created. I26 Parameter initialization via web administration interface. I46 Data is also being transferred or the RAID is being moved. Do not turn off the LinkStation. Have you tried pressing a function key? Only held the concept for about 10 seconds and now it is blue.
Info / Error LED blinks purple when a message appears. The value is flash encoded.
Note. Messages are constantly available (unencrypted) in NAS Navigator2.
Info / Error LED flashes red to indicate an error. The error can be identified by the blinking phenomenon.
How to repair Buffalo Linkstation error I12 ( solved )?
E14 RAID Arrayx E14 Unable to automatically mount data offline to frequently remove problematic disk 1 and then move it to a new disk. Error E22 HDx E22 HDx cannot control I56 License flaw I56 Is there somewhere Buffalo snow chains somewhere post information about one of the modes? Try to remove them yourself with tweezers, an air jacket, or other tool.
Was Sind Die Ursachen Für Den Informationsfehler Buffalo Ls Wvl Und Wie Kann Er Behoben Werden?
Quelles Sont Les Causes De L’erreur D’information Buffalo Ls Wvl Et Comment Y Remédier
Jakie Są Przyczyny Błędu Informacji Buffalo Ls Wvl I Jak Go Naprawić?
Wat Zijn De Oorzaken Van De Buffalo Ls Wvl-informatiefout En Hoe Dit Te Verhelpen?
Buffalo Ls Wvl 정보 오류의 원인과 해결 방법
¿Cuáles Son Las Causas Del Error De Información Buffalo Ls Wvl Y Cómo Solucionarlo?
Vad är Orsakerna Till Buffalo Ls Wvl Informationsfel Och Hur Man åtgärdar Det
Quais São As Causas Do Erro De Informações Do Buffalo Ls Wvl E Como Corrigi-lo
Каковы причины информационной ошибки Buffalo Ls Wvl и как ее исправить
Quali Sono Le Cause Dell’errore Informativo Buffalo Ls Wvl E Come Risolverlo
